AirLive FE-200DM Manuel d'utilisateur

AirLive FE-200DM Manual 1FE-200DM 2-MegaPixel Ceiling Mount Fish Eye PoE IPCAM User’s

1. Introduction AirLive FE-200DM Manual 4 6. Power Jack: The input power is DC 12V, 2A. Note: ONLY use package power adapter supplied with the in

1. Introduction AirLive FE-200DM Manual 511. GPIO: The 7 pin terminal block includes 4 input ports and 1 output ports. 1.4 Mounting the Camera F

1. Introduction AirLive FE-200DM Manual 63. Connect the network cable into the camera, and then mount the camera onto the stand. 4. Rotate the cam

2. Preparation AirLive FE-200DM Manual 72 2. Preparation 2.1 Search and Set up by IPWizard II When you installed the Camera on a LAN environ

2. Preparation AirLive FE-200DM Manual 8 2.2 UPnP of Windows® XP, Vista or 7 UPnP™ is short for Universal Plug and Play, which is a networking

2. Preparation AirLive FE-200DM Manual 9 Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatica

2. Preparation AirLive FE-200DM Manual 10(1) Enable UPnP option of your NAT router To use UPnP IGD function (NAT traversal), you need to make

2. Preparation AirLive FE-200DM Manual 112. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first ti

3. Operating the Network Camera AirLive FE-200DM Manual 123 3. Operating the Network Camera Start-up screen will be as follow no matter an ordi

3. Operating the Network Camera AirLive FE-200DM Manual 13Protocol User can select proper streaming protocol according to networking environme

Copyright and Disclaimer AirLive FE-200DM Manual i Owner's Record The mode

3. Operating the Network Camera AirLive FE-200DM Manual 14z Quad view & Quad with source view PTZ control panel: 1. Ch：Select the channel

3. Operating the Network Camera AirLive FE-200DM Manual 15Volume Click Speaker button to activate this function. Scroll the control bars

4. Administrating the Device AirLive FE-200DM Manual 164 4. 0BAdministrating the Device System Setting This function is only available for a us

4. Administrating the Device AirLive FE-200DM Manual 174.1.2 Advanced z Stream Setting Note: Configuration of stream 2 is the same as strea

4. Administrating the Device AirLive FE-200DM Manual 18z Image Format H.264 and MJPEG are available for image format selection. The term, “i

4. Administrating the Device AirLive FE-200DM Manual 194.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p

4. Administrating the Device AirLive FE-200DM Manual 20 z Audio Setting: Audio Enable: Turn on/off the audio. z Web Record Setting: Save Pat

4. Administrating the Device AirLive FE-200DM Manual 214.2.2 Advanced z White balance: Adjustment to compensate for different environment

4. Administrating the Device AirLive FE-200DM Manual 22z Infrared (IR) Cut Filter: The default is automatically switched according to the lig

4. Administrating the Device AirLive FE-200DM Manual 23(3) Quad with source view: (4) Triple view: 2. Ceiling Mount:

Copyright and Disclaimer AirLive FE-200DM Manual iiFor customers in the U.S.A. This equipment has been tested and found to comply with the

4. Administrating the Device AirLive FE-200DM Manual 24(2.) Broad view: (3.) Quad view: (4.) Quad with source view:

4. Administrating the Device AirLive FE-200DM Manual 25(6.) Triple view: 3. Table Mount: For Choosing Table mount, go back to live vie

4. Administrating the Device AirLive FE-200DM Manual 264. 720P Wall Mount: For Choosing 720P Wall Mount type, go back to Live view. There are

4. Administrating the Device AirLive FE-200DM Manual 274.3 Event 4.3.1 Event Server Add FTP Server: Click on the “Add FTP” to expand FTP s

4. Administrating the Device AirLive FE-200DM Manual 28Remove: Click “Remove” to delete selected event servers. 4.3.2 Motion Detection z To

4. Administrating the Device AirLive FE-200DM Manual 291. Click on “Add” to set up a detection area. (Setup panel will be expanded) 2. Give

4. Administrating the Device AirLive FE-200DM Manual 30 Note: 1. Maximum number of detection window is 10. 2. Motion Detection windows need to

4. Administrating the Device AirLive FE-200DM Manual 314.3.4 Event Configuration 1. To add an event trigger, click on “Add” and the setup

4. Administrating the Device AirLive FE-200DM Manual 32 4.4.2 Storage Display the storage information, including disk size info, type and sta

4. Administrating the Device AirLive FE-200DM Manual 33 z DHCP Service: Stand for Dynamic Host Configuration Protocol. Enable this checked

Copyright and Disclaimer AirLive FE-200DM Manual iiiNOTICE TO USERS © 2006~11 A

4. Administrating the Device AirLive FE-200DM Manual 34The device can directly connect to the xDSL. However, it should be setuped on a LAN envir

4. Administrating the Device AirLive FE-200DM Manual 35z UPnP: Enable UPnP, so that the device can be discovered in an UPnP Compliant Networ

4. Administrating the Device AirLive FE-200DM Manual 36 4.6 System 4.6.1 Information Lists - System and Network configurations. z Firmware V

4. Administrating the Device AirLive FE-200DM Manual 374.6.2 User Use this menu to add, update, or remove the usernames and passwords of the A

4. Administrating the Device AirLive FE-200DM Manual 38Click this option to enable time synchronization with computer time. z Synchronize with

4. Administrating the Device AirLive FE-200DM Manual 39z Factory Default (Including Network setting): Recall the device hard factory defaul

4. Administrating the Device AirLive FE-200DM Manual 40z Backup Setting: To take a backup of all of the parameters, click this button. If

4. Administrating the Device AirLive FE-200DM Manual 41z Use Default Look: The default layout of live/configuration pages. Use Defined Link

5. Appendix AirLive FE-200DM Manual 425 5. Appendix Appendix A: Restore Factory Default In some cases, system does not respond to any operation

5. Appendix AirLive FE-200DM Manual 43Appendix B: Alarm I/O Connector This Network Camera provides a general I/O terminal block as below: Pin

Table of Contents i AirLive FE-200DM Manual Table of Contents 1. Introduction...

5. Appendix AirLive FE-200DM Manual 44Application 1 Application 2 Appendix C: Troubleshooting & Frequently Asked Questions Question Ans

5. Appendix AirLive FE-200DM Manual 45the actual number of connected clients is varying by streaming mode, settings of resolution, codec type,

5. Appendix AirLive FE-200DM Manual 46• If IP address is not assigned to the PC which running IPWizard II program, then IPWizard II program cann

5. Appendix AirLive FE-200DM Manual 47address, it may have changed since you last checked it. • Network congestion may prevent the web page ap

5. Appendix AirLive FE-200DM Manual 48• Network congestion may prevent the Image screen from appearing quickly. You may choose lower resoluti

5. Appendix AirLive FE-200DM Manual 49Internet bandwidth is lower than target bit rate, the video streaming will not work correctly. • Etherne

5. Appendix AirLive FE-200DM Manual 50Make sure the 50 or 60Hz format of your device. • If the object is dark, the image will flicker. Make t

5. Appendix AirLive FE-200DM Manual 51If you want to detect any other devices conflicts with the IP address of Network Camera, also can utiliz

5. Appendix AirLive FE-200DM Manual 52Appendix F: Specifications Camera Model Name FE-200DM Image Device 2 Mega-pixel image sensor Effectiv

5. Appendix AirLive FE-200DM Manual 53Power Consumption 5W IP Level None Vandal proof None Connectors 1 x RJ-45 10BaseT/100BaseTX 1 x DC power

Table of Contents AirLive FE-200DM Manual ii 4.4 Schedule...

5. Appendix AirLive FE-200DM Manual 54(1) Assign a local/fixed IP address to your device The device must be assigned a local and fixed IP Addr

5. Appendix AirLive FE-200DM Manual 55Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to ob

5. Appendix AirLive FE-200DM Manual 56 Enter valid ports in the Virtual Server section of your router. Please make sure to check the box on

5. Appendix AirLive FE-200DM Manual 57z Ethernet Network Environment Normally, DDNS service is only necessary for the users that could only o

5. Appendix AirLive FE-200DM Manual 58(3). After the columns show up at the left side, click “Create Account”. (4). Fill the application agree

5. Appendix AirLive FE-200DM Manual 59Click these two options (5). Check your e-mail mailbox. There will be an e-mail with a title “You

5. Appendix AirLive FE-200DM Manual 60 (6). Enter the web page http://www.dyndns.org/ again. Input your username and password that you just

5. Appendix AirLive FE-200DM Manual 61 (9). Click the “Dynamic DNS”. (10). Click the “Get Started”. (11). We could create a domain name wi

5. Appendix AirLive FE-200DM Manual 621 2 z Setup the DDNS and PPPoE of Networked Device At last, users have to enter the web page of Networke

5. Appendix AirLive FE-200DM Manual 63Austria 230V 50 Hz Brazil 110/220V* 60 Hz *127V found in states of Bahia, Paran? (including Curitib

1. Introduction AirLive FE-200DM Manual 11 1. Introduction 1.1 Overview AirLive FE-200DM is a Fish-Eye Panorama Network Dome Camera featured with

5. Appendix AirLive FE-200DM Manual 64found. United States of America 120V 60 Hz Appendix J: 3GPP To use the 3GPP function, in addition

5. Appendix AirLive FE-200DM Manual 65Appendix K: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your opera

5. Appendix AirLive FE-200DM Manual 66 Click Add/Remove Windows Components The following screen will appear: Select Networking Services Clic

5. Appendix AirLive FE-200DM Manual 67 Select Universal Plug and Play Click Ok Click Next

5. Appendix AirLive FE-200DM Manual 68 Please wait while Setup configures the components. Click Finish

1. Introduction AirLive FE-200DM Manual 2Features z Panoramic 360 Degrees Full View z H.264 & MJPEG Video Compression z 2 Megapixels Resoluti

1. Introduction AirLive FE-200DM Manual 31.3 Physical Overview and Connections 1. Light Sensor: The Light sensor is for detecting IP Camera env