WH-9200AP 802.11a/b/g Dual Radio Wireless Base Station User’s Manual
Access to management interface 1 Please make sure your computer IP is in the same subnet as the WH-9200AP (i.e. 192.168.1.x). 2 Please make sure yo
2. Wirless Settings 2.1 Client + AP Mode In this mode, the Radio1 will operate in 5GHz 802.11a as Client mode while Radio2 will operate in 2.4GHz 8
To connect to an access point, use the “Site Survey” button to find the Access Point. The Site Survey pop up window then shows up and lists availabl
After the access point is selected, its SSID shows automatically in the Network ID (SSID) field. 11 AirLive WH-9200AP User’s Man
WEP WEP allows you to use data encryption to secure your data from being eavesdropped by malicious people. It allows 3 types of key: 64 (WEP64), 12
Rekey interval is time period that the system will change the key periodically. The shorter the interval is, the better the security is. eneral yo
Encryption Type: There are two encryption types TKIP and CCMP (AES). While CCMP provides better security than TKIP, some wireless client stations m
Pre-shared Key: This is an ASCII string with 8 to 63 characters. Please make sure that both the WH-9200AP and the wireless client stations use the
WPA2 WPA2 stands for Wi-Fi Protected Access 2. It provides stronger data protection and network access control then WPA. Only authorized users can ac
WPA2-PSK Enter the Pre-shared Key to initiate WPA2 security. All devices try to access the network should have the matching encryption key. Pre-sha
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits fo
WPA-AUTO Encryption Type: There are two encryption types TKIP and CCMP (AES). While CCMP provides better security than TKIP, some wireless client s
WPA-PSK-AUTO WPA-PSK-AUTO tries to authenticate wireless clients using WPA-PSK or WPA2-PSK. Pre-shared Key: This is an ASCII string with 8 to 63 ch
2.3 Advanced Wireless Settings When click on Advanced Setup button under client mode, a pop-up window appears and show parameter as follow: Beacon In
power-conserving stations that there are packets waiting to be received by them. The DTIM interval specifies how often the beacon frame should contai
The ACK value then shows up after calculating Enter the calculated value of “AckTimeOut” into the appropriate “Ack TimeOut” field (11a or 11g) in th
3. System Management You can review the Device information of your WH-9200AP by the interface. The information shows the current firmware version, I
3.2. System Management Settings The WH-9200AP allow you to change the parameter of manage the system. HTTP Port No.: This is to change the man
Syslog server IP address: The Syslog can also send to the identified IP address. The system log shows in WH-9200AP: 25
3.3. SNMP Settings WH-9200AP can also be managed by remote software with SNMP (simple network management protocol) protocol. System Name: A n
Community String For Write: For read-write operation, you need to configure a write “community string”. Assign a specific name and IP address for you
Table of Contents 1. Introduction ...2 1.1 Overview...
3.4. Firmware Upgrade You can upgrade the firmware of your WH-9200AP (the software that controls your WH-9200AP’s operation). Normally, this is
3.5. Configuration Save and Restore In this interface, you can backup your system configuration to PC and restore your saved configuration file to th
3.6. Reboot System The following interface allows you to reboot your WH-9200AP. Click “Yes” button to reboot. You can also reboot WH-9200AP by
3.7. WH-9200AP Emergency Recovery This document guides to recover your WH-9200AP system if the firmware crashed. 1. Download the tftp server to you
1. Introduction 1.1 Overview The WH-9200AP is a dream device for WISP to build their wireless networks. The WH-9200AP features 2 Atheros that run in
1.2.1 Package Content The WH-9200AP package contains the following items: z One WH-9200AP main unit z 48VDC PoE injector kits z Pole/Wall mount ki
WLAN port when operate in Gateway mode 5 Ground Pin - Reference point for electric current 6 Sluice - Sluice out the water in device N-Typ
Antenna 2 Antenna 2 Pole Mount/Wall mount Installation 5 AirLive WH-9200AP User’s Manual
Power Installation The following image shows the power installation of WH-9200AP. Note that WH-9200AP is IEEE802.3af compatible, you s
1.2.3 Configuration Setups The factory default settings of WH-9200AP are as following: Default Value Settings Wireless1 Wireless2 Device Name WH-92
Commentaires sur ces manuels