AirLive WL-5470AP Manuel d'utilisateur télécharger pdf

5F, No.96, Min-Chuan Rd., Hsin-Tien Dist., New Taipei City 231, TAIWAN

WL-5470AP

802.11g Hi Power Multifunction AP/Router

he WL-5470AP is a multi-function AP designed

for various different wireless applications. On the

hardware side, it features 5 LAN ports and hardware

hi-power amplifier that can boost the output power

from standard 18dBm to over 25dBm*. On the software

front, the WL-5470AP includes both powerful features

and an easy-to-use interface to satisfy the demand of

WISP operators, Home, or Office users.

The WL-5470AP features an incredible 8-mode firmware.

8 Wireless Operating Modes

5-port Hi-Power AP

The most basic mode of multi-function Access Point. In this mode, the AP will

act as a central hub for different Wireless LAN clients. Some hotspot APs

requires 802.1x authenticator function to authenticate a user before

providing Internet service.

AP mode

Also known as Ethernet Client. In this mode, the AP will act as a WLAN card

to connect with the remote AP. Users can connect PC or local LAN to the

Ethernet port of the client mode AP. This mode is mostly used as a CPE device

for WISP subscriber.

Client Mode

In this mode, 2 access points in two remote locations connect to each other

to provide a wireless bridge between 2 remote LANs. It is mostly used by

enterprise to connect 2 remote office's network together. The bridge modes

are connected by using either the WDS (Wireless Distribution System) or

Adhoc topology

Bridge mode

A repeater's function is to extend the wireless coverage of another wireless

AP or router. For WDS repeater to work, the remote wireless AP/Router must

also support WDS function.

WDS Repeater

An universal repeater can also extend the wireless coverage of another

wireless AP or router. But the universal repeater does not require the remote

device to have WDS function. Therefore, it can work with almost any

wireless device.

Universal Repeater

In WISP mode, the AP will behave just the same as the Client mode for

wireless function. However, router functions are added between the wireless

WAN side and the Ethernet LAN side. Therefore, the WISP subscriber can

share the WISP connection without the need for extra router.

WISP (Client Router) mode

In this mode, the AP behaves virtually the same as the WISP mode, except

one thing: the AP can also send wireless signal to the LAN side. That means

the AP can connect with the remote WISP AP and the indoor wireless card,

and then provide IP sharing capability all at the same time! However, the

output power is divided between 2 wireless side and proper antenna

installation can influence the performance greatly.

WISP + Universal Repeater mode

In AP + Router mode. The AP will behave like a broadband router. One of the

LAN port will behave as a WAN port for wired connection to ADSL or Cable

modem. The NAT routing will be performed between the WAN and LAN port.

Making IP sharing possible.

AP + Router mode

Client Mode

WISP

Outdoor AP

WDS Wireless

Router

NoteBook

WDS Repeater

NoteBook

Wireless

Router

Universal Repeater

B A

Client Router

NAT

WISP

Outdoor AP

WISP + Universal

WISP

Outdoor AP

Internet

ADSL or

Cable Modem

Wireless AP

Bridge

LAN

Bridge

LAN

Bridge

LAN

Bridge

LAN

WLAN PCI

WLAN USB

Wireless AP

1 2 3

Résumé du contenu

Page 1 - WL-5470AP

5F, No.96, Min-Chuan Rd., Hsin-Tien Dist., New Taipei City 231, TAIWANWL-5470AP802.11g Hi Power Multifunction AP/Routerhe WL-5470AP is a multi-functio

Page 2 - FEATURES & SPECIFICATIONS

5F, No.96, Min-Chuan Rd., Hsin-Tien Dist., New Taipei City 231, TAIWAN- AP, Bridge, Client, Repeater functions - Router and Gateway mode - WISP Client

Page 3 - Ordering Information:

5F, No.96, Min-Chuan Rd., Hsin-Tien Dist., New Taipei City 231, TAIWAN- 2MB Flash, 16MB SDRAM- Reversed SMA Antenna Port- Power, LAN, WLAN LED indicat